My Blog

1. The technical characteristics of compound fertilizer granulator, the granulation rate is more than 90%, and the specification is incomplete, it can also enter the pulping machine again for secondary processing, and the cylinder power is small. The shell is made of wear-resistant steel, which effectively extends the service life of the equipment.

2. The reducer of the granulator drives the belt through the motor. There is a pinion on the shaft of the reducer, which coincides with the teeth on the outer gear ring of the machine body. The barrel and the reducer are close to each other, and the material is removed from the bin or hopper. The conveyor belt is sent to the end of the barrel, the material is made into small granular material in the barrel, and the material is discharged from the barrel. The outlets at the other end are together. Through the continuous operation of the machine, mass production can be realized.

3. Power saving support roller bracket is used for support. The support frame is made of high quality carbon steel, which can fully bear the weight of the cylinder. Considering the large friction between the cylinder and the supporting wheel, it is intentionally used in this part. On the one hand, more wear-resistant materials can improve the integrity and stability of the equipment.

4. The transmission device is an important part that provides the main movement for the machine. The ring gear on the cylinder is driven by the motor and reducer on the rack.

5. The shelf is made of special non deformable special channel steel, which is used for dry connection, making the transmission device of the machine more complete and stable. This is a special molding machine, which can be made by rolling materials by chemical reaction in a certain liquid. Under the action of the cylinder, through the rolling of the cylinder, the material and small particles are extruded to form a sphere.

Precautions for using granulator fertilizer:

1. Always pay attention to the temperature change of the fuselage. When touching the strip with clean hands, raise the temperature immediately. Until the silver bar touches your hand, this is normal.

2. When the bearing part of the reducer is burned or accompanied with noise, it should be shut down for repair in time and refuel.

3. When the bearing parts at both ends of the main engine bearing chamber are hot or noisy, please stop the machine maintenance and add butter. During normal operation, the bearing cavity is filled with grease every 5-6 days.

4. Pay attention to find out the operation rules of the machine; for example, if the temperature of the machine is high or low, the speed is fast or slow, it can be handled in time according to the situation.

5. When the fuselage is unstable, check whether the gap between the couplings is too tight, and adjust and loosen it in time.

The common straw crushers are corn straw crusher, branch crusher, peanut shell grinder and so on. It is material crushing equipment in organic fertilizer processing and feed processing. Moreover, the utilization rate of straw crusher in various fields is very high, just like the straw crusher in fertilizer processing, it is not only useful in the early stage of livestock manure treatment, straw, mushroom residue and other auxiliary materials crushing.

Application skills of straw crusher:
(1) The machine should be fixed on the ground and can be fixed with cement. If the working place needs to be changed frequently, the crusher and motor should be installed on the frame made of angle steel.

(2) After installation, carefully check whether the machine is firmly installed. Whether the motor shaft and pulverizer shaft are parallel, at the same time, check whether the drive belt tightness is appropriate.

(3) Before starting, rotate the rotor by hand to check whether the operation is flexible and normal, whether there is collision in the casing, whether the rotation direction of the rotor is correct, and whether the lubrication of the motor and crusher is good.

(4) Do not change the belt wheel of the grinder frequently, in case the speed is too high or too low.

(5) After the machine is started, it should be idled for 2 to 3 minutes before feeding.

(6) When working, the machine should feed evenly. If there is noise, the temperature of bearing and body is too high or the material is sprayed out, the machine should be shut down immediately for inspection and troubleshooting.

(7) Before crushing, the staff should carefully check the materials to prevent the metal, stone and other hard objects from entering the crushing room and causing accidents.

(8) When feeding, the staff should stand on the side of the straw crusher to prevent being hurt by the anti ejected debris. When crushing long stalks, hands should not be held too tightly to prevent them from being brought in.

(9) Stop feeding before shutdown, and cut off the power supply after the materials in standby are cleared. Cleaning and maintenance should be carried out after shutdown.

(10) After 300 hours of operation, the bearing must be cleaned and the oil must be changed; when loading the oil, it is better to fill 1 / 3 of the bearing seat gap, not more than 1 / 2. When the machine is stopped for a long time, the drive belt should be removed.

Welcome to get free inquiry to our straw crusher: https://fertilizerplantequiment.com/